How do you light the pilot on a Trane?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light.
Where is the pilot light on my Trane furnace?
Take off the furnace cover and locate the gas valve and the gas control, which is a plastic or metal knob with three settings: “on,” “off” and “pilot.” You’ll see three tubes coming from the bottom of the gas valve.
How do you relight an automatic pilot light?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.
How do you turn on a pilot light?
Turn the gas regulator valve to the “pilot” position. If the water heater has a manual “ignite” button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.
How do you reset the pilot light on a Trane furnace?
If your furnace has a pilot light, it will be controlled by a knob on the bottom of your unit. You can easily relight the pilot light by turning the knob to ‘off,’ waiting a minute, then setting it back to ‘on. ‘ This will stop and restart the gas flow of your furnace.
Where is reset button on Trane furnace?
Turn off the power and open up the control panel to access the reset buttons on these models. Next, lift the cover to the blower compartment, and you should see the reset button sitting next to the blower motor and blower wheel.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How much does it cost to relight a pilot light?
A plumber can help reignite the pilot light. They will charge you an hourly fee of $40 to $150. This is usually a fairly brief project, and may just take an hour.
How do you relight a furnace pilot light?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
Where is the reset button on a Trane xv80?
If you look inside the blower motor fan, you should find the reset button. Look for a small red or yellow button on the side of the blower motor. If you do not see one on the side of the motor that is facing you, feel around to the back of the motor housing for the button.
What causes the pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
Why does my Trane furnace have a pilot light on?
Furnace manufacturers have all but phased out standing pilot ignition systems for gas furnaces, so if you have to light the pilot light on your Trane furnace, it’s because the furnace is more than 20 years old.
Can you replace the igniter on a Trane XE60?
These ignitors can wear out quickly, but they’re usually inexpensive and easy to replace. Older furnaces, such as the Trane XE60, don’t have these LEDs, and if the furnace isn’t producing heat, you have to visually inspect the burner to see if the pilot is on.
How do I know if my XE60 furnace needs servicing?
Older furnaces, such as the Trane XE60, don’t have these LEDs, and if the furnace isn’t producing heat, you have to visually inspect the burner to see if the pilot is on. If the pilot is off, you can relight it yourself, but there’s a reason it went off, and that may indicate the need for servicing.
How do you light the pilot on a Kenmore gas range?
Hold a lit long-reach lighter over the pilot orifice until the pilot starts to burn. Continue holding in the gas control to give the thermocouple time to heat up. This usually takes 10 to 20 seconds. Release the gas control knob and verify that the pilot flame continues to burn.