Is 6011 electrode positive or negative?
6011 runs on AC and direct current electrode positive (DCEP), while 6010 runs only on DCEP. This gives 6011 an advantage if you have an AC-only machine.
Which lead is positive on a stick welder?
This “work” terminology simply means that it is where your ground clamp lead should go. So, for a majority of stick welding, Positive polarity (DCEP) is the best route. Most rods are designed with this polarity in mind, and that won’t change anytime soon.
Is 6011 reverse polarity?
E6010 electrodes are intended for direct current (DC) only. While E6011 electrodes can be used on alternating current (AC), as well as DC. Whether it is DC+ (electrode positive or “reverse”) polarity or DC- (electrode negative or “straight”) polarity, DC produces smoother welding output than AC.
Can you run 6011 on DC?
While the 6011 was specifically designed for AC machines, it can also run on DC giving it an advantage over the 6010 electrodes (which can only do Direct Current Electrode Positive). A common mistake for Stick welders is to treat their 6013 electrodes like 6011 or 6010 rods.
Can you use 6011 to weld cast iron?
Yes, but it makes an almost useless weld. It also requires that the cast iron be preheated above 500 degrees F (or preferably dull red heat) and cooled at a very slow rate. The problem is that cast iron is brittle and shrinkage will generally cause cracks in the heat affected zone around the melted metal.
Is TIG electrode positive or negative?
TIG welding is typically done with Direct Current Electrode Negative (DCEN) polarity, and in alternating current (AC). Welding with DCEN polarity is typically used for welding steel, stainless steel, copper, and most other materials that are weldable. AC is typically used for welding aluminum and magnesium.
Is MIG welding electrode positive or negative?
MIG welding requires DC electrode positive, or reverse polarity. The polarity connections are usually found on the inside of the machine. Set gas flow.
What is the best setting for 6011 welding rod?
about 85 amps is a good place to start. Much colder and your puddle will not flatten out. Much hotter and you might struggle with arc blow toward the end of each rod. machines differ and some folks like to weld hotter, but 85 amps will get you in the ball park.
What are 6011 rods used for?
E 6011 electrode is a general-purpose electrode performs welding in all positions and efficiently in vertical-up and over-head positions; it is used mainly for sheet metal welding and low silicon deposit application. The electrode arc is easy to control and produces a flat weld bead with light slag formation.
What makes a 6011 electrode the most versatile?
Two factors, quick cooling and being able to weld in different positions makes this electrode one of the most versatile in the market. What takes these rods to a whole different level is the fact that 6011 electrodes can also work with multiple types of welders because they run on AC, DC+, and DC-.
What is a 6011 welding rod used for?
What takes these rods to a whole different level is the fact that 6011 electrodes can also work with multiple types of welders because they run on AC, DC+, and DC-. This rod can be used for almost anything that requires deep penetration, no matter the polarity options you have on a welder or the position you have to weld in.
What is the difference between 6011 and 6010?
Make sure the area around you is clear, especially below if you are working up high. Cutting with these electrodes produces big-time sparks and large globs of molten metal. 6011 runs on AC and direct current electrode positive (DCEP), while 6010 runs only on DCEP. This gives 6011 an advantage if you have an AC-only machine.
What polarity do 6011 rods work with?
The 6011 rods work with any polarity. You don’t have to stress about whether you have a cracker box, DC- or a fancier machine that can handle different polarities and AC frequencies, the 6011 will perform with all of these. You will have one less thing to worry about while using these rods.