What is B camshaft position sensor?
The camshaft position sensor notes the rate at which the camshaft is spinning, and helps the car’s computer control things like fuel injection and engine timing. Note that the “B” means that this sensor is located in the exhaust side of the cylinder head.
How do you fix trouble code P0017?
What repairs can fix the P0017 code?
- Resetting the engine fault codes and verifying that the problem is still occurring.
- Replacing the camshaft position sensor on a failed camshaft bank.
- Repairing or replacing the wiring connection to the camshaft sensor or the OCV.
- Replacing the Engine Control Module.
What is a camshaft position correlation bank 1 sensor B?
What Does the P0017 Code Mean? Diagnostic trouble code (DTC) P0017 stands for “Camshaft Position B – Camshaft Position Correlation (Bank 1).” Like P0016, this code indicates that your car’s powertrain control module (PCM) detects a misalignment between the crankshaft and camshaft positions.
Can I drive with a P0014 code?
While you can still drive around with P0014 registered issues, please don’t do it. Driving with it will cause hard starting, erratic idling, stalling, poor engine performance, and increased fuel consumption. Again, if a lousy VVT control solenoid triggers the issue, it may cause other related components to fail.
How do you fix a camshaft position correlation Bank 1 sensor?
The most common solution to this code is the replacement/repair of wiring, followed by replacement of crankshaft/camshaft position sensors if the engine timing is known to be good. Less common solutions include replacement of reluctor rings, or VVT/VCT oil control solenoids.
Can I drive with code P0017?
Is Code P0017 Serious? There are few codes more severe than a P0017 code. Don’t drive your vehicle – even to the repair shop. A mistimed engine can quickly lead to severe engine damage and even total the engine.
Where is the crankshaft position sensor located?
The sensor is at either the front or the back of the crankshaft, so it’s usually located either on the transmission bellhousing or behind the crankshaft pulley. There should be a small air gap, usually about a millimeter or two, between the sensor and the reluctor.
Where is the crankshaft position sensor Bank 1?
Beneath the timing belt cover is where the CMP Sensor is mounted. The camshaft position sensor can be found in the right side of the engine compartment at the rear of the valve cover.
What does Bank 1 sensor B mean on a car?
Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B) What does that mean? This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc.
What does a crankshaft position sensor do?
The crankshaft position sensor (CKP) relays crankshaft position and engine RPM to the PCM, or ignition module. This information is used but the PCM to control ignition timing, and in some applications, it is also used to control fuel injection. The two common CMP and CKP designs are Hall Effect and permanent magnet.
What does the p0017 code on a crank position sensor mean?
P0017 is a diagnostic trouble code (DTC) for “Crankshaft Position-Camshaft Position Correlation (Bank 1 Sensor B)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What is the DTC code for crankshaft position correlation?
Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor B) This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Ford, Dodge, Toyota, VW, Honda, Chevrolet, Hyundai, Audi, Acura, etc.