Why pool creepy-crawly not moving?
If Kreepy Krauly is not moving or not pulsating. Check that the main drain and all suction lines are closed, except for the suction line to which Kreepy Krauly is attached (usually a skimmer). Check for debris in the filter or [pump basket]. Check that pool pump is not on low speed.
Where do pool hose weights go?
Hose weight placement depends on the depth of the pool. For pools 4′ deep or less, use 1 hose weight 4″ to 12″ from the cleaner. For pools of 4-7′ deep, use 2 weights, one 4″ to 12″ from the cleaner and one 6′ from the cleaner. For pools from 8′ to 12′ deep, use a third weight, placed 10 ft.
How do you remove the Kreepy Krauly flapper?
RELEASE BAFFLE PLATE – The Flapper is constrained by the Baffle Plate. To remove the Baffle Plate, lift the lip of the foot pad and insert a flat-headed screwdriver along side one of the two tabs on the Baffle Plate. Push the tab inward until the Baffle Plate releases.
Where do you put the weights on a creepy crawly?
For pools 4′ deep or less, use 1 hose weight 4″ to 12″ from the cleaner. For pools of 4-7′ deep, use 2 weights, one 4″ to 12″ from the cleaner and one 6′ from the cleaner. For pools from 8′ to 12′ deep, use a third weight, placed 10 ft. from the swivel end of the cleaner.
Why does my Kreepy Krauly not sit flat?
It’s all about getting the right amount of flow through the diaphragm so it levels out and works right. That adapter allows for adjustments due to different sized pumps so it can ge dialed in for more or less suction. Well I did install the part where I can control the suction and it still doesn’t want to lay flat.
How long should Kreepy Krauly run?
about 2-4 hours
HOW LONG SHOULD A KREEPY KRAULY RUN? Just as long as it needs to, which is generally about 2-4 hours depending on the size of the pool and the amount of debris. Best practice is to remove Kreepy from the pool after you are satisfied with the results.
How long should my Kreepy Krauly hose be?
Measuring the ideal length for your hose is a matter of calculating the distance of the two furthest points in your swimming pool. So, for example; If your skimmer is located 30 feet from the furthest corner, and your pool has a depth of 5 feet, you will need a 35-foot-long vacuum hose.
Where do weights go on Kreepy Krauly hose?
How do I install the Kreepy Krauly?
Here’s all you have to do after you buy your Kruiser: Assemble the Kreepy Krauly with enough hose to reach the full length of your pool. Attach the fitting to the suction port in the skimmer. ( Careful not to have the pump running) Then connect the hose to the fitting through the front skimmer flap.
How do you use A Kreepy Krauly pool cleaner?
ATTACH HOSE TO THE CLEANER – Check that the swivel head rotates freely and then attach the hose to the swivel head. PLACE CLEANER INTO POOL – Lower the Pentair Kreepy Krauly Cleaner and hoses into pool. Push the hose straight down to purging all air out of the cleaner and hose.
Why is my Kreepy Krauly cleaner not working properly?
Your pump may be too small. DECREASE CLEANER SPEED – If you have an especially powerful pump, it may be overpowering the automatic regulator valve. To slow the Kreepy Krauly Cleaner down, you may have to replace the bottom part of the regulator valve with a manual by-pass valve.
When does the Pentair Kreepy Krauly cleaner begin to work?
The Cleaner will begin to operate as soon as the pump is fully primed. CHECK CLEANER ANGLE – The Pentair Kreepy Krauly Cleaner should be operating with its seal moving flat on the pool floor and the drive tubes making a 45 degree angle with the floor. If required, adjust the hose weights one inch at a time until proper angle is achieved.